Please select To the mobile version | Continue to access the desktop computer version
123
Return to list New
Author: titoche78

BT3 pro freeze randomly

[Copy link]

2

Threads

46

Posts

276

Credits

Full Member

Rank: 3Rank: 3

Credits
276
Post time 2019-05-23 21:48:17 | Show all posts
beelink replied at 2019-05-22 14:27
Hello
In the case of power-on, the reset hole is the reset button, and the BIOS setting is restore ...

the reset hole is behind the bt3 back near the headphone hole,
insert a small paper clip with the PC on and hold for 15/20 seconds
Reply Support Not support

Use magic Report

0

Threads

1

Posts

14

Credits

Newbie

Rank: 1

Credits
14
Post time 2019-10-02 01:25:35 | Show all posts
same problem
After 6-12 hours the PC freeze
Intel Support Assistant and windows all updated

windows 10 home
version 1903
Reply Support Not support

Use magic Report

0

Threads

5

Posts

32

Credits

Newbie

Rank: 1

Credits
32
Post time 2019-10-12 19:17:51 | Show all posts
You should update your drivers
Reply Support Not support

Use magic Report

0

Threads

1

Posts

16

Credits

Newbie

Rank: 1

Credits
16
Post time 2020-01-05 15:27:35 | Show all posts
It may be because the CPU falls into deep sleep states.
Microsoft has a way of avoiding that see below:

From Microsoft Support (for a different issue, but still helpful):

You can disable the Advance Configuration and Power Interface (ACPI) C-states by using a BIOS firmware option on the computer. If the firmware does not include this option, a software workaround is available. You can disable the ACPI C2-state and C3-state by setting a registry key. To do this, follow these steps:

1. At a command prompt, run the following command:
reg add HKLM\System\CurrentControlSet\Control\Processor /v Capabilities /t REG_DWORD /d 0x0007e066

2. Restart the computer.

Note The computer idle power consumption will increase significantly if the deeper ACPI C-states (processor idle sleep states) are disabled. Windows Server 2008 R2 uses these deeper C-states on the Xeon 5500 series as a key energy-saving feature.

To continue to benefit from these energy-saving states, remove the registry key that you set in step 1 after you install the hotfix that this article describes. To do remove the registry key, follow these steps:

1. At a command prompt, run the following command:
reg delete HKLM\System\CurrentControlSet\Control\Processor /v Capabilities /f

2. Restart the computer.
Reply Support Not support

Use magic Report

0

Threads

1

Posts

14

Credits

Newbie

Rank: 1

Credits
14
Post time 2020-01-20 04:57:01 | Show all posts
My Beelink BT3 with Windows 10 was randomly freezing, I solved by changing the setting in BIOS:
Press ESC or F2 during boot do enter BIOS setup, and configure as follow:
Goto "ACPI Settings" and change:
    Enable ACPI Auto Configuration = Disabled
    Enable Hibernation = Disabled
    ACPI Sleep State = Suspend Disabled
    Lock Legacy Resources = Disabled
Goto "PPM Configuration" and change:
    CPU C State Report = Disabled   
Exit saving changes.

Hope this helps.
Reply Support Not support

Use magic Report

1

Threads

3

Posts

41

Credits

Newbie

Rank: 1

Credits
41
Post time 2020-04-01 00:36:35 | Show all posts
Reply Support Not support

Use magic Report

You have to log in before you can reply Login | Sign up

Points Rules

Close

Webmaster RecommendedPrevious post /1 Next post

Quick Reply To Top Return to the list